The Perspecta multi-directional sound system was designed by Robert Fine of Fine Sound Inc., the equipment was manufactured by the American electronics company Fairchild. As would be expected for that era, it used valve amplifiers.

Although frequently referred to as stereo, Perspecta is not true stereo. The Perspecta system provided a system of electronically switching the mono sound track to any of three speaker systems placed behind the screen in a left-centre-right set up. The sound could be sent to one, two or all three speakers simultaneously. Despite the fact that the sound was directional, it was still only a single mono sound track. Perspecta’s own advertising generally described their system as Multi-directional sound.

Comparing a well mixed Perspecta sound presentation with today’s Dolby stereo, the first thing that becomes apparent is that the sound is capable of following the performers on the screen. When an actor on screen right speaks, the sound comes from screen right, if another person speaks from screen left, the sound comes from screen left. This gives a true directional sound effect. This is not the case with Dolby stereo surround, which mainly confines the dialogue to the centre channel, with left-right stereo music and effects. There are technical reasons why this is so, but that’s another story.

The secret of Perspecta lies in the use of three low frequency tones to control the directional switching of the sound. These tones are recorded along with the usual music, dialogue and sound effects onto the normal mono optical sound track.

When in operation, if the Perspecta unit detects the presence of one or more of these sub-audible tones, it will automatically switch the decoder into Perspecta mode. From there on the presence or otherwise, of the individual sub-audible tones will determine which speakers are turned on or off. Although only the one sound track is present on the film, these tones will determine whether it will be switched to the left, centre or right speaker(s) or any combination of them.

The Perspecta decoder also incorporates a high pass filter circuit, which eliminates these low frequency tones from the auditorium speaker system. However, they are used internally in the Perspecta unit to control the switching of the sound to the three speaker systems. The frequency of these sub-audible tones are 30 Hz. ( cycles per second ) controlling the left speaker, 35 Hz. for centre channel and 40 Hz. for the right. There is one shortcoming with the system. Because there is only the one sound track available, when the sound is switched from one speaker to another to move with the action on the screen, if there is a musical background, the music will also follow the action. At first thought appear to be quite disconcerting, but it operation, is barely noticeable.

Although Perspecta saw it’s demise in the early 1960s, a company in England is making new fully solid state decoders for 300 pounds. These units plug directly into the latest Dolby processor units and have the added enhancement of providing rear speaker drive when all three Perspecta ‘channels’ are present.

OPERATION

The basic block diagram above shows the signal flow through the Perspecta unit. Starting at the left side the sound from the operating projector is amplified in the pre amplifier and fed to the two filter stages. The high pass filter rejects the low frequency Perspecta tones, but passes all of the normal sound track audio through and feeds it to the three control gates. In the normal or non-Perspecta mode, the centre channel is always turned on and the sound is conveyed to the centre amplifier and speaker system in the normal way.

The low pass filter allows only the Perspecta low frequency control tones to pass through. They are applied to the detector stage, which determines if the film is in Perspecta, and if is, the three control gates are switched into Perspecta mode by the Perspecta on/off line. The control tones are also applied to the three filter stages. These filters are quite sharp, producing an output only if the exact corresponding frequency is present. The three outputs are connected to detectors ( not shown ) , which produce a voltage if the corresponding frequency is present. The detector’s output voltage is used to turn on it’s control gate, in the on position, it sends the sound track audio to the following amplifier stage, and then to the speakers.

Because the filters are quite sharp, their bandwidth is only about + or - 2 Hz, the speed of the projector is quite critical. A one frame per second speed error can be sufficient to create problems.

Although there is no real reason why the Perspecta system would not operate satisfactorily with 16mm, all of the 16mm Perspecta releases that I have been able to check, have not had the Perspecta tones recorded. Also, MGM and others have re-released some of their ‘Classic Cartoons’ from the 1950s, these too are being reprinted without the Perspecta encoding.

References: 1. - International Projectionist, early 1950s. 2. - Tiles of cartoon Daredevil Droopy (1951) show "Perspecta Sound" . 3. - Widescreen Movies by Robert E. Carr & R.M. Hayes. Publishers McFarland & Co.

Footnotes: 1. Many of the well known 1950s releases were released in Perspecta versions, including most of the Paramount VistaVision releases as well as the Tom & Jerry CinemaScope cartoons. Unfortunately, there appears to be no authoritative listing available.